-
description - Customer Reviews
Gtechniq Crystal Serum Light 30ml
Barcode 5060147721010
Product Code CS 0.03
Why use Gtechniq Crystal Serum Light?
Crystal Serum Light is the prosumer version of the world famous Gtechniq Accredited Detailer only Crystal Serum - a coating so hard that if applied incorrectly can only be removed by using 1,500 grit sand paper.
Serum Light offers 80% of Professional Serum’s performance, but if applied incorrectly can be machine polished from your vehicle’s paintwork.
When it comes to adding gloss, resisting swirls, contaminant and dirt repellence, Gtechniq Crystal Serum and Serum Light are the pinnacle in paint protection."
Storage and Use
To apply CSL your vehicle must be indoors and it must remain indoors for at least 12 hours after application
Wash and then decontaminate your vehicle’s paintwork with Gtechniq W5 Citrus All Purpose Cleaner and W6 Iron and General Fallout Remover. If required, clay your paintwork to remove other bonded contaminants
If needed, polish your paintwork either by machine or by hand to remove any imperfections
Spray Gtechniq Panel Wipe onto a Gtechniq MF1 ZeroR Microfibre Buff Cloth
With your panel fully cooled after polishing, taking care to avoid any paint protection film or other types of vinyl film, buff away all polish residues. This process ensures you will get the maximum number of chemical bonds between the coating and your vehicle’s paintwork
Put on the gloves provided to prevent CSL coming into contact with your skin
Soak the application pad with two full measures from the pipette and work the liquid into the padt to get an even saturation
Replace the lid on the bottle and set aside - do not keep the bottle in your hand as this promotes premature curing
Apply with applicator provided in overlapping strokes to an area roughly 2’ x 2’, or work to the bodylines of the vehicle
After coating a single small panel or half a larger panel, remove residue with MF1 ZeroR Microfibre Buff Cloth. Always remove from further than you have applied, working from the outside in. It is essential to check for residue
You may need to buff the same area several times to remove residue. We recommend using two microfibre cloths at any one time. Please note that you are only removing excess product
When working with coatings, we recommend you inspect the panels with a bright but diffuse light source and not with bright spot lights which are very poor for spotting coating residue
Avoid buffing with too much force as this can spoil the surface you are protecting, and you may also drag the partially cured coating off the surface
Take care that the microfibre cloths you are using are rotated sufficiently and quickly so that CSL does not partially cure in the cloth, this will make buffing residue significantly more difficult
If you miss removing residue and it cures fully, you should re-polish this area, and reapply CSL
As soon as you finish put the microfibres in water and wash and dry them as soon as possible
Use CSL within 1 year of purchasing, for best results, once opened use within 3 months
Store opened bottles in a dry and cool storage area that's out of direct sunlight
Storage and Use
To apply CSL your vehicle must be indoors and it must remain indoors for at least 12 hours after application
Wash and then decontaminate your vehicle’s paintwork with Gtechniq W5 Citrus All Purpose Cleaner and W6 Iron and General Fallout Remover. If required, clay your paintwork to remove other bonded contaminants
If needed, polish your paintwork either by machine or by hand to remove any imperfections
Spray Gtechniq Panel Wipe onto a Gtechniq MF1 ZeroR Microfibre Buff Cloth
With your panel fully cooled after polishing, taking care to avoid any paint protection film or other types of vinyl film, buff away all polish residues. This process ensures you will get the maximum number of chemical bonds between the coating and your vehicle’s paintwork
Put on the gloves provided to prevent CSL coming into contact with your skin
Soak the application pad with two full measures from the pipette and work the liquid into the padt to get an even saturation
Replace the lid on the bottle and set aside - do not keep the bottle in your hand as this promotes premature curing
Apply with applicator provided in overlapping strokes to an area roughly 2’ x 2’, or work to the bodylines of the vehicle
After coating a single small panel or half a larger panel, remove residue with MF1 ZeroR Microfibre Buff Cloth. Always remove from further than you have applied, working from the outside in. It is essential to check for residue
You may need to buff the same area several times to remove residue. We recommend using two microfibre cloths at any one time. Please note that you are only removing excess product
When working with coatings, we recommend you inspect the panels with a bright but diffuse light source and not with bright spot lights which are very poor for spotting coating residue
Avoid buffing with too much force as this can spoil the surface you are protecting, and you may also drag the partially cured coating off the surface
Take care that the microfibre cloths you are using are rotated sufficiently and quickly so that CSL does not partially cure in the cloth, this will make buffing residue significantly more difficult
If you miss removing residue and it cures fully, you should re-polish this area, and reapply CSL
As soon as you finish put the microfibres in water and wash and dry them as soon as possible
Use CSL within 1 year of purchasing, for best results, once opened use within 3 months
Store opened bottles in a dry and cool storage area that's out of direct sunlight.
Barcode 5060147721010
Product Code CS 0.03
- 3-5 years durability
- Incredible gloss
- Best possible DIY swirl mark and chemical resistance
Why use Gtechniq Crystal Serum Light?
Crystal Serum Light is the prosumer version of the world famous Gtechniq Accredited Detailer only Crystal Serum - a coating so hard that if applied incorrectly can only be removed by using 1,500 grit sand paper.
Serum Light offers 80% of Professional Serum’s performance, but if applied incorrectly can be machine polished from your vehicle’s paintwork.
When it comes to adding gloss, resisting swirls, contaminant and dirt repellence, Gtechniq Crystal Serum and Serum Light are the pinnacle in paint protection."
Storage and Use
To apply CSL your vehicle must be indoors and it must remain indoors for at least 12 hours after application
Wash and then decontaminate your vehicle’s paintwork with Gtechniq W5 Citrus All Purpose Cleaner and W6 Iron and General Fallout Remover. If required, clay your paintwork to remove other bonded contaminants
If needed, polish your paintwork either by machine or by hand to remove any imperfections
Spray Gtechniq Panel Wipe onto a Gtechniq MF1 ZeroR Microfibre Buff Cloth
With your panel fully cooled after polishing, taking care to avoid any paint protection film or other types of vinyl film, buff away all polish residues. This process ensures you will get the maximum number of chemical bonds between the coating and your vehicle’s paintwork
Put on the gloves provided to prevent CSL coming into contact with your skin
Soak the application pad with two full measures from the pipette and work the liquid into the padt to get an even saturation
Replace the lid on the bottle and set aside - do not keep the bottle in your hand as this promotes premature curing
Apply with applicator provided in overlapping strokes to an area roughly 2’ x 2’, or work to the bodylines of the vehicle
After coating a single small panel or half a larger panel, remove residue with MF1 ZeroR Microfibre Buff Cloth. Always remove from further than you have applied, working from the outside in. It is essential to check for residue
You may need to buff the same area several times to remove residue. We recommend using two microfibre cloths at any one time. Please note that you are only removing excess product
When working with coatings, we recommend you inspect the panels with a bright but diffuse light source and not with bright spot lights which are very poor for spotting coating residue
Avoid buffing with too much force as this can spoil the surface you are protecting, and you may also drag the partially cured coating off the surface
Take care that the microfibre cloths you are using are rotated sufficiently and quickly so that CSL does not partially cure in the cloth, this will make buffing residue significantly more difficult
If you miss removing residue and it cures fully, you should re-polish this area, and reapply CSL
As soon as you finish put the microfibres in water and wash and dry them as soon as possible
Use CSL within 1 year of purchasing, for best results, once opened use within 3 months
Store opened bottles in a dry and cool storage area that's out of direct sunlight
Storage and Use
To apply CSL your vehicle must be indoors and it must remain indoors for at least 12 hours after application
Wash and then decontaminate your vehicle’s paintwork with Gtechniq W5 Citrus All Purpose Cleaner and W6 Iron and General Fallout Remover. If required, clay your paintwork to remove other bonded contaminants
If needed, polish your paintwork either by machine or by hand to remove any imperfections
Spray Gtechniq Panel Wipe onto a Gtechniq MF1 ZeroR Microfibre Buff Cloth
With your panel fully cooled after polishing, taking care to avoid any paint protection film or other types of vinyl film, buff away all polish residues. This process ensures you will get the maximum number of chemical bonds between the coating and your vehicle’s paintwork
Put on the gloves provided to prevent CSL coming into contact with your skin
Soak the application pad with two full measures from the pipette and work the liquid into the padt to get an even saturation
Replace the lid on the bottle and set aside - do not keep the bottle in your hand as this promotes premature curing
Apply with applicator provided in overlapping strokes to an area roughly 2’ x 2’, or work to the bodylines of the vehicle
After coating a single small panel or half a larger panel, remove residue with MF1 ZeroR Microfibre Buff Cloth. Always remove from further than you have applied, working from the outside in. It is essential to check for residue
You may need to buff the same area several times to remove residue. We recommend using two microfibre cloths at any one time. Please note that you are only removing excess product
When working with coatings, we recommend you inspect the panels with a bright but diffuse light source and not with bright spot lights which are very poor for spotting coating residue
Avoid buffing with too much force as this can spoil the surface you are protecting, and you may also drag the partially cured coating off the surface
Take care that the microfibre cloths you are using are rotated sufficiently and quickly so that CSL does not partially cure in the cloth, this will make buffing residue significantly more difficult
If you miss removing residue and it cures fully, you should re-polish this area, and reapply CSL
As soon as you finish put the microfibres in water and wash and dry them as soon as possible
Use CSL within 1 year of purchasing, for best results, once opened use within 3 months
Store opened bottles in a dry and cool storage area that's out of direct sunlight.
Write an online review and share your thoughts with other shoppers!
Be the first to review this product
